SKU:RB-01C016 Arduino 網絡擴展板

產品概述

以W5100為核心的Arduino Ethernet網絡擴展模塊，可以使Arduino成為簡單的Web服務器或者通過網絡控制讀寫Arduino的數字和模擬接口等網絡應用?？芍苯邮褂肐DE中的Ethernet庫文件便可實現一個簡單Web服務器。同時該版本的支持mini SD卡（TF卡）讀寫，功能強悍，不容錯過！該擴展板采用了可堆疊的設計，可直接插到Arduino上，同時我們的其他擴展板也可以插上去。

規格參數

W5100特性

支持SPI接口(SCS、SCLK、MISO、MOSI)，接線方便，程序簡單；
支持硬件TCP/IP協議棧，支持TCP,UDP,ICMP,IGMP,IPv4，ARP,PPPoE.
內嵌10BaseT/100BaseTX以太網物理層；
支持自動通信握手(全雙工和半雙工)；
端口支持3種工作模式(客戶端、服務端、UDP)；
支持4個獨立端口同時運行；
內部集成16KBYTE收發緩存；
支持自動極性轉換（DMI/MDIX）；

W5100優勢

W5100硬件集成TCP/IP協議棧、MAC、PHY，減少了用戶代碼量、減輕了CPU的壓力，而相對便宜的ENC28J60只集成MAC和PHY，TCP/IP協議棧須要用戶在上層代碼中實現；
W5100可以通過SPI接口控制，只須要操作少量的寄存器即可，大量節約了開發時間.
W5100是通過SPI發指令、數據操作寄存器，不同平臺移植W5100的程序更加方便、簡單；

使用方法

接線方法

1.將網絡擴展板與UNO插接在一起，確保引腳連接正常。

2.如圖所示連接UNO和PC機，下載代碼到UNO控制器中

例子程序

/*
  Web Server
 
 A simple web server that shows the value of the analog input pins.
 using an Arduino Wiznet Ethernet shield. 
 
 Circuit:
 * Ethernet shield attached to pins 10, 11, 12, 13
 * Analog inputs attached to pins A0 through A5 (optional)
 
 created 18 Dec 2009
 by David A. Mellis
 modified 9 Apr 2012
 by Tom Igoe
 
 */

#include <SPI.h>
#include <Ethernet.h>

// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network:
byte mac[] = { 
  0xDE, 0xAD, 0xBE, 0xEF, 0xFE, 0xED };
IPAddress ip(192,168,1,177);

// Initialize the Ethernet server library
// with the IP address and port you want to use 
// (port 80 is default for HTTP):
EthernetServer server(80);

void setup() {
 // Open serial communications and wait for port to open:
  Serial.begin(9600);
   while (!Serial) {
    ; // wait for serial port to connect. Needed for Leonardo only
  }


  // start the Ethernet connection and the server:
  Ethernet.begin(mac, ip);
  server.begin();
  Serial.print("server is at ");
  Serial.println(Ethernet.localIP());
}


void loop() {
  // listen for incoming clients
  EthernetClient client = server.available();
  if (client) {
    Serial.println("new client");
    // an http request ends with a blank line
    boolean currentLineIsBlank = true;
    while (client.connected()) {
      if (client.available()) {
        char c = client.read();
        Serial.write(c);
        // if you've gotten to the end of the line (received a newline
        // character) and the line is blank, the http request has ended,
        // so you can send a reply
        if (c == '\n' && currentLineIsBlank) {
          // send a standard http response header
          client.println("HTTP/1.1 200 OK");
          client.println("Content-Type: text/html");
          client.println("Connection: close");  // the connection will be closed after completion of the response
	  client.println("Refresh: 5");  // refresh the page automatically every 5 sec
          client.println();
          client.println("<!DOCTYPE HTML>");
          client.println("<html>");
          // output the value of each analog input pin
          for (int analogChannel = 0; analogChannel < 6; analogChannel++) {
            int sensorReading = analogRead(analogChannel);
            client.print("analog input ");
            client.print(analogChannel);
            client.print(" is ");
            client.print(sensorReading);
            client.println("<br />");       
          }
          client.println("</html>");
          break;
        }
        if (c == '\n') {
          // you're starting a new line
          currentLineIsBlank = true;
        } 
        else if (c != '\r') {
          // you've gotten a character on the current line
          currentLineIsBlank = false;
        }
      }
    }
    // give the web browser time to receive the data
    delay(1);
    // close the connection:
    client.stop();
    Serial.println("client disonnected");
  }
}

3.將網絡擴展板使用網線與電腦連接