“SKU:RB-02S088 電流檢測傳感器”的版本間的差異

來自ALSROBOT WiKi
跳轉至: 導航、 搜索
?產品相關推薦
?資料下載
 
第112行: 第112行:
 
[[文件:erweima.png|230px|無框|右]]
 
[[文件:erweima.png|230px|無框|右]]
 
* 產品資料
 
* 產品資料
?
下載鏈接:https://pan.baidu.com/s/1eyvGuEPQsPI9Vxs4mKra4w
+
下載鏈接: https://pan.baidu.com/s/1RXJZvWrutHLR0PZsKxVOWg
?
提取碼:uc0o  <br/>
+
提取碼:o9si
 
* 產品購買鏈接:http://lifestyle201.com/goods-689.html
 
* 產品購買鏈接:http://lifestyle201.com/goods-689.html

2021年10月8日 (五) 11:40的最后版本

Dianliuchuanganqi002.jpg

目錄

產品概述

此產品由一個電流感應器TA12-200組成構成??梢詫⒋蟮碾娏髁哭D(zhuǎn)換為幅度小的電壓量輸出。該模塊采用沉金工藝,外觀更加美觀,同時采用防插反3Pin接口,操作更加安全,插口一邊有大寫字母A表示該模塊位模擬量傳感器,另一邊是電流表的圖標標志表示該模塊具有測試電流的功能。此產品可以應用于交流電的電流檢測,最大可檢測的電流為5A。

規格參數

  1. 工作電壓 :+5v
  2. 最大檢測電流:5A
  3. 檢測類型:交流電
  4. 尺寸大?。?0mm x 25mm
  5. 重量大小:8g
  6. 信號類型:模擬信號
  7. 孔徑:4.96mm
  8. TA12 - 200 電流互感器參數:
02S088001.png
  1. 接口定義
  • S:信號引腳
  • NC:不需要連接
  • -:電源地


工作原理

電流傳感器是根據電磁感應原理設計的,本傳感器使用一個線圈,導線穿過線圈,當導線中產生交流電時,由于電磁感應的原因,模塊的線圈中會產生電流,從而使 Arduino 的模擬接口感測到,通過 Arduino 控制器自帶的 10 位 AD 轉換來讀取信號。

使用方法

example1_Arduino

  • 主要硬件
  • 硬件連接
實物連接圖
連接圖

引腳接線說明:

傳感器引腳 所接引腳
電位計模塊 + 引腳 穿過電流傳感器接在UNO的D13 S 引腳
電位計模塊 S 引腳 振動馬達 S 引腳
電位計模塊 - 引腳 懸空
電流傳感器 控制器 A0 引腳
振動馬達 + — 引腳 分別接在控制器Vcc和GND


注:NC可以不接

  • 示例程序
#define ELECTRICITY_SENSOR A0 
int mada = 13;
float amplitude_current;                 

void setup() 
{
	Serial.begin(9600); 
	pins_init();
        pinMode(mada, OUTPUT);  
}
void loop() 
{
        digitalWrite(mada, HIGH);  
	int sensor_max;
	sensor_max = getMaxValue();
	Serial.print("sensor_max = ");
	Serial.println(sensor_max);
	//the VCC on the RobotBase interface of the sensor is 5v
	amplitude_current=((float)sensor_max * (5 / 1024)) / 800 * 1000 * 2000;// 輸入電流,單位mA
						
	Serial.println("The amplitude of the current is(in mA)");
	Serial.println(amplitude_current,1);//Only one number after the decimal point
}
void pins_init()
{
	pinMode(ELECTRICITY_SENSOR, INPUT);
}
int getMaxValue()
{
	int sensorValue;         
	int sensorMax = 0;
	uint32_t start_time = millis();
	while((millis()-start_time) < 1000)//sample for 1000ms
	{
		sensorValue = analogRead(ELECTRICITY_SENSOR);
		if (sensorValue > sensorMax) 
		{
		sensorMax = sensorValue;
		}
	}
	return sensorMax;
}
  • 程序效果

程序正常編譯上傳以后,打開 Arduino IDE 自帶的串口監視器之后,會顯示出當前檢測到的電流值。

02S0880401.png

資料下載

Erweima.png
  • 產品資料

下載鏈接: https://pan.baidu.com/s/1RXJZvWrutHLR0PZsKxVOWg 提取碼:o9si